n Light Weight. For footnotes refer to the last page. IRHM REF: MIL-PRF- / TOAA. This datasheet has been downloaded. 2N 2NU. JANSR (K RAD(Si)). JANSF (K RAD(Si)). ABSOLUTE MAXIMUM RATINGS (TC = +25°C unless otherwise noted). Parameters / Test. 2N datasheet, 2N pdf, 2N data sheet, datasheet, data sheet, pdf, Microsemi, N-Channel.
|Country:||Republic of Macedonia|
|Published (Last):||6 October 2007|
|PDF File Size:||9.25 Mb|
|ePub File Size:||17.81 Mb|
|Price:||Free* [*Free Regsitration Required]|
E, f, c, or M with hot solder dip 9 Types A, 6, Z, 0.
Annealed copper-clad steel wire shall nave me same retirements as – Tor copper-clad steel wire specified in 3. Jsf 1M0PM Finish 31 is no longer available on the current revision of the specification.
Dimensions in inches taxless otherwise specified. Detailed 2b7269 requirements for each of the electrical parts. F’rt— 1 jiu in. Any parts failing lot not exceeding PDA for group A, subgroup 1see 4. AD core sizes ran be provided in non- metallic phenolic or plasticaluminum, or Xatasheet Guaranteed Voltage Breakdown coated aluminum boxes.
For glass to metal sealed products, all devices with terminals which are solder dipped to the seal shall pass screen 7 of table IV. The type of insulation consists of a two digit codes. Dle ana tons Is inches unlees atherwlae specified.
Use of tin plating is prohibited as a final finish and as an undercoat see 6 8. The tin-lead thickness after fusing or reflowshall not be less than microinches 2 54 pm at any single point. The inductors are open coil E. Send dtasheet regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Washington Headquarters Services, Directorate for Information Operations and Reports, Jefferson Davis Highway, SuiteArlington, VAand to the Office of Management and Budget, Paperwork Reduction ProjectWashington, DC Parts that define the lead finish as other than pure tin in the.
The matte-tin plating shall contain no more than 0 05 percent by weight codeposiled organic material measured as elemental carbon Minimum lead content shall be 3 percent.
Drawing number PD defines the material properties of the dataheet in the following paragraph, 3. Datashedt by part number with the quantity used per assembly for the electrical components.
DPA report 1 identifies the package as ceramic with no tin platting, see following insert. The thickness of the gold plating shall be to microinches. The wire type is 05, gold plated; 0. Both the package and the leads are gold platted. The finish required by the following Motorola drawing PE is electroless nickel and gold.
Lab Par wsc Typa: The part numher shall consist oflhc hasic MS number. Pure tin may not be used to coat any surface see H 4.
For glass- to -metal sealed products, all devices with terminals which are solder dipped to the seal shall pass screen 7 of table IV. Zinm cadmium or pure tin shall not be used as a finish material. A pure tin finish is not prohibited. Parts that define the plating finish in their procurement specification, but do not specifically prohibit the use of a pure tin finish.
The package finish is not specified. The device type Tkwber shall be es specified in the associated detail spec l f Ication or SO the numbers Shall consist o’ two digits atsiprwd saquant ially, froa 01 to W within each associatad detail specification or SMC.
Cores are available in all IEEE standard sizes and over 1, special sizes. This note prohibits the use of pure unalloyed tin finish on all surfaces.
Use of tin lead finishes are acceptable provided that the minimum lead content is 3 percent. The use of pure tin plating is not prohibited in the drawing and the package finish is not specified. The type at lamllt: